Effect of weld parameters on the mechanical properties of friction-stir-welded heat-treatable AA6061-T6
Author affiliations
DOI:
https://doi.org/10.15625/2525-2518/57/6/13808Keywords:
friction stir welding AA6061-T6, hardness, tensile strength, bending strength, impact energyAbstract
Effect of welding parameters on the mechanical properties of the friction stir welding of heat-treatable 6061-T6 was experimentally investigated. The influence of the welding rates on the hardness, tensile strength, bending strength, and the impact energy of the welding were investigated. The experimental results showed the joint could be obtained with free defects. However, both the tensile and bending strength of the joint were quite low compared to that of the base alloy 6061. The bending ductility of the joints were improved significantly. While the impact resistance at around the welded zone was higher than that of the base alloy, the impact resistance at the weld center was remarkable low.Downloads
References
REFERENCES
. Gene M. - The welding of aluminium and its alloys, Woodhead Publishing Ltd, Cambridge England (2002).
. Mishra R.S., Mahoney M.W. editors - Friction Stir Welding and Processing, ASM International (2007).
. Tran Hung Tra - Effect of weld parameters on the mechanical properties of friction stir welding AA6063-T5, ASEAN Engineering Journal, 2229-127X 4 (2011) 73-81.
. Hao D.D., Okazaki M., Tra TH., Nam Q.H. - Defects Morphology in the Dissimilar Friction Stir Welded T-lap Joints of AA7075 and AA5083, Advances in Engineering Research and Application (2019) 210-216.
. Tran Hung Tra, Seino M., Sakaguchi M., Okazaki M. -Fatigue crack propagation behavior relevant to inhomogeneous microstructure of friction stir welding AA6061-T6, Journal of solid mechanics and materials engineering 4 (6) (2010) 840-848.
. Tran Hung Tra, Masakazu Okazaki, Kenji Suzuki - Fatigue crack propagation behavior of friction stir welding AA 6063-T5: Residual stress and microstructure effect, International Journal of Fatigue 0142-1123 43 (2012) 23-29.
. Shiva chander M., Satish Kumar P., Aruri Devaraju - Influence of Tool Rotational speed and Pin Profile on Mechanical and Microstructural Characterization of Friction Stir Welded 5083 Aluminium Alloy, Materialtoday: Proceedings, Vol. 5 (2) Part 1 (2018) 3518-3523.
. Aruna Prabhaa Prasad K., Kumar Puthab Balla, Srinivasa Prasad - Effect of Tool Rotational Speed on Mechanical Properties Of Aluminium Alloy 5083 Weldments in Friction Stir Welding, Materialtoday: Proceedings Vol. 5 (9), Part 3 (2018) 18535-18543.
. Callister W.D. - Materials Science and Engineering - An Introduction, John Wiley & Sons, Inc. (2007) 188-198.
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Vietnam Journal of Sciences and Technology (VJST) is an open access and peer-reviewed journal. All academic publications could be made free to read and downloaded for everyone. In addition, articles are published under term of the Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA) Licence which permits use, distribution and reproduction in any medium, provided the original work is properly cited & ShareAlike terms followed.
Copyright on any research article published in VJST is retained by the respective author(s), without restrictions. Authors grant VAST Journals System a license to publish the article and identify itself as the original publisher. Upon author(s) by giving permission to VJST either via VJST journal portal or other channel to publish their research work in VJST agrees to all the terms and conditions of https://creativecommons.org/licenses/by-sa/4.0/ License and terms & condition set by VJST.
Authors have the responsibility of to secure all necessary copyright permissions for the use of 3rd-party materials in their manuscript.
Vietnam Journal of Science and Technology (VJST) is pleased to notice: